Buy a quality Taylor Made custom boat cover in Ultima, Hotshot or PolyCotton fabric and receive a free vent and pole! Taylor Made boats covers are sewn with Gore Tenara thread. The stitching is guaranteed for the life of the fabric.
Why a vent and pole? Don’t let your interior suffer while stored for the winter from mold and mildew damage. Proper ventilation can keep these boat destroying fungi from attacking your boat! The patented Boat Vent II installs quickly and easily, with no screws or fasteners. The venting area provides for greater volume of exhaust air while closing the top to bottom gap – increased air movement while keeping water out!
May 25, 2011
Go2marine offers Taylor-Made T-top Center Console Boat Covers for boats with fixed position “T” tops. These boat covers are built to accommodate a wide range of vessels, from 17.5′ to 26.4′. There are two groups of T-top covers, those that fit boats with no bow rails to 6″ bow rails and another group for those with taller rails, from 6″ up to 18″ bow rails. If you are uncertain how to measure your boat, follow these simple measurement guidelines.
Fabric and Construction:
The semi-custom T-top boat cover is manufactured from 6 ounce Hot Shot with a 5 year limited warranty. Exclusive for Taylor-Made boat covers, engine covers and other fabric products, they are now sewn together with Gore Tenara thread. The thread is resistant to UV sunlight, saltwater, chemicals, acid rain and harsh environments; in fact, Gore stands behind the Tenara thread and guarantees that it will outlast ANY fabric it is sewn with. From the Acrylic Coated Polyester to the strap buckles and straps, these covers are made to stand up to years of service.
Unlike T-top boat covers of the past, this pattern allow for two major design improvements.
- The cover is made in 2 sections that can be zipped together
- The cover can be installed by just one person – without a ladder.
After removing the cover from the box, separate the front and the back sections. Place the bow section over the bow and pull the cover on until it reaches the center cockpit. You may need to work from side to side. Now do the same with the stern section, pulling it on until it reaches the center console. Standing on the deck, secure and zip down one side 1/2 way, then the other side. Pull the zipped cover up under the T-top and secure. Step off the boat and zip the cover the rest of the way down on both sides.
Secure the zipped portion of the boat cover down on each side. Once you are done with the zippers and securing the straps across the zipper, move to the bow. Install the trailer strap on the bow, then work towards the stern. Here are the Complete T-Top Coat Cover Installation Instructions.
The result is a fabric boat cover that keeps out the elements and protects your investment for years to come.
April 18, 2011
Go2marine with Taylor Made Marine Products is offering a drawing of $500 Gift Card for one lucky boater. Enter the Taylor Made Sweepstakes.
Taylor Made manufacturers a complete source of marine products and accessories. From the dock edging and guards right next to your boat to the fenders, buoys and mooring whips that keep your boat from contacting the dock. Taylor Made offers bimini tops, anchor shade umbrellas, misting systems and other products to protect you from the sun while on your boat as well as boat covers to keep your boats finish looking like new.
Tenara thread is now used in all Ultima and Hotshot fabric products including boat covers, biminis and motor hoods. Tenara thread is guaranteed to outlast ANY fabric that it is used to sew – this means no more seams separating because the thread has failed to live up to the sun or weather.
Sweepstakes ends June 15th, 2011. No purchase necessary. See details below**
**You must be 18 years or older to enter. No purchase necessary. $500 Gift Card will be issued from a major credit card company. See full sweepstakes rules and details here.
February 25, 2010
A boat cover will protect the topsides and interior of your boat from weather as well as reduce moisture or sun damage coming in from the environment. The number one enemy of a boat’s interior during the off-season is moisture, second only to the harmful damage of solar rays. In addition, boat covers, covered with Ultra Violet coating, can prevent the harsh rays of the sun from causing damage to your boat. Find more answers to your boat cover questions here.
September 29, 2009
For most people, there comes a time when the boat must be put away for the season, the cabin locked up and all is left to fend for itself through the slumber of the winter. In most locations, you will use a boat cover or store a small boat in open or unheated storage. Larger boats will be secured to the dock or hauled out and winterized. The number one thing that people complain about is the smell when you get back to the boat in the spring. Go2marine is here to offer you some understanding about what happens during the winter with moisture and what can be done to protect your boat.
If your boat is small, you should first get a boat cover to protect the topsides and interior from weather and reduce moisture coming in from the environment. If your boat is large, you will need to seal it up well; yet still supply some form of ventilation. The number one enemy of the interior of boats in the off season is moisture.
Fungus (Fungi) consist of molds, mildews, yeasts and more, in this unique Kingdom that is neither animal nor plant. Fungi are part of the natural environment and operate primarily by breaking down dead organic matter such as fallen leaves and dead trees. Indoors, fungus growth tries to break down dead matter (wood, cotton, rayon and other organic materials) as well as pseudo-organic materials (like foam, polyester). Fungi reproduce by many means, including tiny spores; the spores are invisible to the naked eye and float through outdoor and indoor air. The more commonly recognizable mold and mildew may begin growing indoors when mold spores land on surfaces that are wet. There are many types of mold, and few of them will grow without water or moisture. This Kingdom makes up the most diverse life on the planet with worldwide distribution and some 1.5 million species. Fungi also has the ability to become an allergen, irritant or significant pathogen to humans.
Fungi gradually destroy the things that they grow on. Ultimately Fungi thrive as a result of a high level of moisture encouraging their growth; rather than trying to just treat the fungi to kill them, resolve the moisture issue to prevent the problem that encourages Fungi growth.
Requiring Power – For boats that are left within the reach of an extension cord or dock cord you can help keep moisture to a minimum with a number of heater or dehumidifier options.
GoldenRod Dehumidifiers offer inherent safety features like no fan, simple installation, constant heat output and simplicity. They eliminate dampness, mildew, condensation and humidity with size options for areas from 100 to 500 cubic feet.
Extreme (Xtreme) Heaters takes a higher tech, more active approach to keeping moisture in control. The XtremeHeater Boat Heater is a heating element that is self-regulated at a pre-set temperature and automatically varies its wattage in order to maintain that pre-set temperature.
Non-Powered – If you leave your boat and there is no means to power anything, you still have several options.
Hard mounting vents are are installed in the cabin top or on hatches and used when leaving your vessel for the season, while it is uncovered but still weather-tite. The big news here is solar vents that have the advantage of a fan without leading power wires.
There are a variety of moisture control devices that rely on a ‘salt’ like Calcium Chloride to draw moisture from the surrounding air and can be used in nearly any location, onboard or under cover. The most common of these is the Dri-Z-Air Dehumidifier.
Lastly, if you have a boat cover, a vent with support pole can help in any season with moisture control. This system is easily installed with a pair of scissors and your hands for a clean vent installation.
September 10, 2009
In most areas of the country, the summer season of boating is drawing to a close. Protect your boat with a new boat cover from Go2marine; all major boat cover manufacturers are covered here! At Go2marine, we would like to share some ideas and information to help you choose and use your boat cover… lest your cover end up like this sad picture.
There are a number of things that can be done to extend the life of your boat cover and the ability to protect the investment in your boat. You will need to make choices for a cover based on your local, environmental and storage conditions – then on the boat cover fabric.
Not all fabrics are equal. There are four main factors that affect how durable, waterproof, breathable and stable the boat cover fabric is. The following factors affect your choice of selection.
- Poly/cotton (65/35) blends are the least expensive fabric, typically, they are warranted for only a year.
- Polyester is often a mid to top range fabric, typically followed up with a three or five year warranty depending on the fabric weight.
- Acrylic is the top end material, usually only in heavier weight fabrics (9 0z. plus).
The industry standard for a marine fabric is the venerable Sunbrella marine fabric, with the Pacific Blue being the single most popular color in marinas everywhere. All boat cover manufacturers offer either Sunbrella or Sunbrella equivalent fabrics.
- Fabric weight is measured in ounces per square yard.
- The weight of the fabric is often (but not always) telling of both the warranty and lifespan.
- Heavier fabrics are in the 9 oz. range, lightweight fabrics are in the 6.5 oz. range.
- How tightly woven the fabric is will indicate durability – a tighter fabric will last longer.
- How big the weaving threads (thread count) are will also indicate durability – the smaller the threads for a given weight will produce a more durable fabric.
- A 9 oz. tight weave fabric will last longer than a 13 oz. course weave fabric.
- Of interest here; Marine or Pacific Blue (a middle blue) seems the most stable color.
- Reds and Yellows fade faster and wear out sooner than other colors.
Boat cover manufacturers and their fabrics: Manufacturer – Fabric Name, Material, Weight and Warranty.
Top of the line fabrics are represented by:
- Taylor Made – Ultima, Polyester, 7 oz., 5 year.
- Westland – Sunbrella, Acrylic, 9.25 oz., 5 year.
- ShoreMaster – Prism, Polyester, 9 oz., 5 year.
- Carver – Poly-Guard, Polyester, 8 oz., 5 year.
Middle range fabrics are represented by:
- Taylor Made – Hot Shot, Polyester, 6.25 oz., 5 year.
- Westland– Sharkskin, Polyester, 6.5 oz., 5 year.
- ShoreMaster – Sunburst, Polyester, 6.5 oz., 3 year.
Where you store your boat and the environmental conditions it is subjected to will affect the life of the cover. How you set up the cover for storage with one of the many options, will also effect the usefulness and longevity of the boat cover.
Taking the dockside example above, there are a number of things that could be done to help the boat cover do a better job…
Get a pole. The single cheapest way to prop up the cover and prevent water pooling while also offering ventilation is with a vented pole assembly. They are incredibly easy to install in any cover, in virtually any location.
Get a strap system. This is useful for the large cockpit expanse on most boats and will prevent the huge, tearing puddle that can happen. Mounts at four corners connecting at the center with a pad on pole arrangement.
Get some Bows. It is hard to beat a system of Boat Cover Bows with their matching Sockets for keeping the cover arched. This is the most foolproof way to keep the boat dry and it gives you a fighting chance against snow.
Remember: Choose the fabric for the cover that will last the best for your application. If the boat is stored outside, year round, tailored or subjected to harsh conditions then a Top of the line fabric is what you want. If your boat is stored under a carport, on a lift and you are usually good with handling the cover, get the middle range line of fabrics. Lastly, if you are just looking for a “dust cover” to protect your boat while stored, then the base poly/cotton cover will work fine.
December 20, 2007
Trailerable boat covers often come with a tighter fit and straps to keep the cover snug while trailering. However, if you are just looking for a cover to your boat dry and aren’t planning on trailering it any time soon, Taylor Made Products makes a line of economy covers that may fit with your budget.
Westland, TaylorMade Products, and ShoreMaster all make trailerable boat covers. These covers are either custom made to your boat’s make and model or come in a less-snug, semi-custom boat cover version that is less expensive.
Westland’s custom boat covers come with 1/4″ draw rope in the hem for a snug fit as well as 12 straps with buckles for securing the cover. Taylor Made Products custom boat covers are secured with tie down straps made from 1″ wide heavy duty webbing, plus a nylon rope in the boat cover hem with patented rope lock for cinching the cover tight.